Archive for RCA

RCA BA-72A Preamps

Posted in Racked Modules, Restored with tags , , , , , , , , , , , , on January 22, 2014 by AnalogAudioRepair

A client in Los Angeles wanted a pair of RCA BA-71 preamps racked with the option of using them to run some stereo tracks through.  These use the same circuit as the BA-31 (minus power supply) and the BA-72.  I had a few BA-72A modules in stock and came up with this single space rack mount solution.  First the modules were tested, re-capped and tested again.  Then I built a power supply with 30 VDC for the preamps and 48 VDC phantom power.  The modules were wired with a switchable 20dB pad as well as a switch to change the input transformer from 150 ohms to 600 ohms.  With both the pad and 600 ohm setting, the preamps can take up to 0dBm input without clipping.  Of course the output is +20dBm at that point, so I added 600 ohm attenuators to the output.  Everything fit nicely in the single rack unit and I put collars around the +48 switches, original RCA knobs on the outputs, and a black and silver RCA “meatball” logo on the front panel for good measure!

recapped RCA BA-71 72 31 transistor preamplifier

Recapped Preamp

connecting RCA preamps BA series discrete transistor

Wiring in Progress

Wiring RCA preamp rack BA-72A

Wired Up

RCA BA-71 vintage preamplifier front

Front View

RCA BA-72A Preamp back panel

Back Panel

RCA BA-72 discrete preamp controls

Controls

RCA meatball logo on BA-72A preamp

Meatball Logo

 

 

 

 

 

 

Vintage Tube Mixer Direct Ouputs (RCA, Ampex, Altec, Etc.)

Posted in Modded with tags , , , , , , , on July 30, 2013 by AnalogAudioRepair

Not a lot of great pictures this time, but something I do get requests for.  There are quite a few nice tube mixers around that sum two or more inputs into a single output.  Often folks would like to use these as individual mic preamps with their own outputs.  Your only choice is to use them as a single channel pre, or add some sort of direct out.

The issue is that these preamps use a single tube (or half of a dual triode) to amplify each input, then one or more tubes for EQ and output stages.  Of course it would be costly to add identical output stages to each channel, even if the power supply could handle it.  So the quick and dirty method is to take an unbalanced signal right off the coupling capacitor from the first stage.  The downside is that these outputs can’t drive much of a load, and have a reduced level compared to the main outs.  The upside is that they generally work well into the high impedance inputs of most converters and other modern gear.  Also, by using a switching jack, the signal can be connected to/disconnected from the mix buss automatically.

I have done this recently with a vintage RCA mixer (MI-C38690) and an Ampex MX-35 and both clients were quite pleased with the results.  The RCA also got input pads and a nice panel for all the connectors as well as some power supply cleanup.  The Ampex was additionally modded with line inputs on the first two channels.

RCA tube mixer with input pads and direct outs

RCA tube mixer with input pads and direct outs

RCA Tube Mixer Wiring

RCA Tube Mixer Wiring

RCA Power Supply Mess - Before Servicing

RCA Power Supply Mess – Before Servicing

Ampex MX-35 Line Inputs

Ampex MX-35 Line Inputs

Ampex MX-35 Direct Outs

Ampex MX-35 Direct Outs

RCA BA-2C Tube Preamp

Posted in Restored with tags , , , , on February 26, 2013 by AnalogAudioRepair

This vintage RCA vacuum tube preamplifier was missing it’s power transformer.  Fortunately I had the schematics and a transformer that would fit the bill.  A couple power resistors were required to get the voltages spot on, but in the end it worked out well.  The unit got a full re-cap and a fresh set of New Old Stock vacuum tubes.  The new owner even received an original manual!

RCA BA-31 Preamps

Posted in Racked Modules with tags , , , , , , on August 5, 2012 by AnalogAudioRepair

A pair of vintage RCA BA-31 discrete transistor microphone preamps with Daven output attenuators.